Kti-networks KCD-400 Series Bedienungsanleitung

-1-INDUSTRIAL1000BASE-T TO 1000BASE-XMEDIA CONVERTERSKCD-400 SeriesInstallation GuideDOC.060227-KCD-400

-10-CertificateFCC Part 15 Class BCE/EMC EMI EN50081-1 Class BEMS EN55024CE/LVD Safety EN 60950EN 50081-1/1992 :EN55022:1994/A1:1995/A2:1997EN61000-3-

-11-1.3 Special FunctionsAuto MDI/MDI-X FunctionThis function allows the copper port to auto-detect the twisted-pair sig-nals and adapts itself to fo

-12-Far End Fault FunctionThe fiber port is facilitated with this function. When the fiber port detectsa link failure on its receiving circuitry, it w

-13-2. Installation2.1 UnpackingCheck that the following components have been included:• Information CD• The Media Converter unit• DIN-rail mounting b

-14-2.2 Safety CautionsTo reduce the risk of bodily injury, electrical shock, fire, and damage tothe equipment, observe the following precautions.• D

-15-2.3 DIN-Rail MountingIn the product package, a DIN-rail bracket is installed on the device formounting the converter in a industrial DIN-rail encl

-16-The final mechanical dimensions after installing DIN rail mounting bracketare:

-17-2.4 Panel MountingThe device is provided with an optional panel mounting bracket. Thebracket support mounting the device on a plane surface secure

-18-The screw locations and final dimension are shown below:

-19-2.5 Applying PowerThe power specifications of the device are:Operating Voltage +7 ~ +30VDCPower Consumption Max. 2.5W @30VDCThe device provides t

-2-(C) 2005 KTI Networks Inc. All rights reserved. No part of this documen-tation may be reproduced in any form or by any means or used to makeany dir

-20-Power wires: 24 ~ 12AWG (IEC 0.5~2.5mm2)Install the power source wires with the plug properly. Screw the wire withplug securely. Then, plug in DC1

-21-Using DC Power JackDC Jack Connector: Jack D 6.3mm D 2.0mmAC Power Adapters: Optional commercial rated adapters are availablefor purchasing.Rate

-22-2.6 Power Failure Relay OutputThe device provides a relay output to report power failure event to aremote alarm monitoring system. The replay outp

-23-2.7 Making Twisted Pair Copper Port ConnectionCopper port is featured to support connection to :• Auto-negotiation devices• Auto-negotiation incap

-24-2.8 Making Fiber Port ConnectionThe mini-GBIC (SFP) port must be installed with an SFP fiber trans-ceiver for making fiber connection. The device

-25-3 LED IndicatorsThe following figure shows the locations of the configuration switchesand LED indicators:3.1 LED IndicatorsLED DISPLAY STATE INTER

-26-Appendix: Model Optical SpecificationsThe media converter series provides the following fiber options:Model SpecificationsReference OperatingKCD-4

-3-The information contained in this document is subject to change withoutprior notice. Copyright (C) All Rights Reserved.TRADEMARKSEthernet is a regi

-4-Table of Contents1. Introduction... 51.1 Features ...

-5-1. IntroductionThe industrial 1000BASE-T to 1000BASE-X media converter series pro-vides industrial strength Ethernet copper-to-fiber media conversi

-6-1.1 Features• Gigabit copper to fiber conversion: 1000Base-T-to-1000Base-SX/LXover multimode or single-mode fiber• SFP design : For flexibility, an

-7-1.2 SpecificationsThis figure shows the important components of the converter:

-8-Twisted-Pair Interface (Copper Port)Connector Shielded RJ-45Signal Compliance IEEE 802.3ab 1000BASE-T std.Pin Assignments Auto MDI/MDI-X detectionD

-9-DC Power InterfaceInterface Screw-type terminal block 1. Two pairs for power wire cascading 2. One pair for power failure relay outputDC Jack (-D