KTI Networks KCD-3PB Installationsanleitung

-1-INDUSTRIAL10/100BASE-TX TO 100BASE-FXMEDIA CONVERTERSKCD-300 SeriesInstallation GuideDOC.060221-KCD-300

-10-DC Power InputInterface Screw-type terminal block( 2 sets for power wire cascading)DC Jack (-D6.3mm/+D2.0mm)Operating Input Voltages +7V ~ +30V(+5

-11-CertificateFCC Part 15 Class BCE/EMC EMI EN50081-1 Class BEMS EN55024CE/LVD Safety EN 60950EN 50081-1/1992 :EN55022:1994/A1:1995/A2:1997 CISPR Cla

-12-1.3 Model SpecificationsThe media converter series provides the following fiber options:Model SpecificationsModel FX Con. Wavelength Fiber Distanc

-13-1.4 Special FunctionsAuto MDI/MDI-X FunctionThis function allows the TP port to auto-detect the twisted-pair signalsand adapts itself to form a va

-14-Link Fault Pass Through FunctionWhen this function is enabled, a link fault detected on the TP port willforce a link down on the FX port. Similarl

-15-2. Installation2.1 UnpackingCheck that the following components have been included:• Information CD• The Media Converter unit• DIN-rail mounting b

-16-2.2 DIN-Rail MountingIn the product package, a DIN-rail bracket is provided for mounting theconverter in a industrial DIN-rail enclosure.The steps

-17-5. Screw the clamp with the bracket and make sure the converter isproperly fixed on the DIN rail.

-18-Make sure that there are proper heat dissipation from and adequate ven-tilation around the device.The final mechanical dimensions after installing

-19-2.3 Mounting on a Panel SurfaceAn optional mounting bracket, as shown below is also available for mount-ing the converter on a panel surface such

-2-(C) 2006 KTI Networks Inc. All rights reserved. No part of this documen-tation may be reproduced in any form or by any means or used to makeany dir

-20-2. Mount and screw the converter on the target surface. The finaldimension after bracket installation is also shown below:Make sure that there are

-21-2.4 Applying PowerThe converter provide two types of power interfaces, terminal block and DCpower jack for receiving DC power input from external

-22-DC2 + and DC2 - can be installed with another power-pair for delivering themain power input to next converter in a cascading way.Note: Only up to

-23-2.5 Making TP Port ConnectionTP port is featured to support connection to :• Auto-negotiation devices• Auto-negotiation incapable 10BASE-T devices

-24-2.6 Making FX Port ConnectionFX port operates on 100Mbps and full duplex (factory default). A varietyof fiber options is provided as listed in Sec

-25-3 Configuration Switches & LED IndicatorsThe following figure shows the locations of the configuration switchesand LED indicators:Refer to the

-26-3.1 Configuration SwitchesSW FUNCTION SETTING & STATESW1 TP Port mode OFF Auto-negotiation (default)ON Forced modeSW2 TP Port Duplex OFF Full

-27-3.1.1 Forwarding Mode Setting SW5The following table lists the forward method used in different TP to FXconversions:SW5 Setting TP port to/from FX

-28-3.1.3 FX Duplex Setting SW7This setting is used to set the duplex mode of the FX port. It is recom-mended to use full duplex mode for FX connectio

-29-3.2 LED IndicatorsLink Fault Pass Through Function is disabledLED DISPLAY STATUS & INTERPRETATIONPWR Power status ON Power onOFF Power offTP L

-3-The information contained in this document is subject to change withoutprior notice. Copyright (C) All Rights Reserved.TRADEMARKSEthernet is a regi

-4-Table of Contents1. Introduction...51.1 Features ...

-5-1. IntroductionThe industrial 10/100BASE-TX to 100BASE-FX media converter series pro-vides industrial strength Ethernet copper-to-fiber media conve

-6-1.1 Features• Convert speed and media type• Support full wire speed conversion• Support 10Mbps and 100Mbps speed on TP (copper) connections• Auto M

-7-1.2 SpecificationsThis figure shows the important components of the converter:

-8-Twisted-Pair Interface (TP Port, Copper Port)Connector Shielded RJ-45Pin Assignments Auto MDI/MDI-X detectionSignal Compliance IEEE 802.3 10Base-T,

-9-Configuration Setting Switches (SW)NO. FUNCTION SETTINGSSW1 TP Port mode OFF Auto-negotiation (default)ON Forced modeSW2 TP Port Duplex OFF Full d