KTI Networks 6-Port Bedienungsanleitung

-1-KGS-612FWeb Smart 6-Port Gigabit Ethernet Switchwith Fiber ConnectivityUser,s ManualDOC.071005

-10-Software Management FunctionsInterfaces Web browserManagement objects System configuration - IP settings, Name, PasswordPort configuration control

-11-2. Installation2.1 UnpackingThe product package contains:• The switch unit• One power adapter• One product CD-ROM2.2 Safety CautionsTo reduce t

-12-2.4 Mounting the Switch on a Din-rail ChassisThe switch also can be mounted on a din-rail chassis.The steps are:1. Screw the din-rail mounting bra

-13-2.6 Reset ButtonThe reset button is used to perform a reset to the switch. It is not used in normal cases and can be usedfor diagnostic purpose.

-14-2.8 Making Fiber ConnectionThe SFP slot must be installed with an SFP fiber transceiver for making fiber connection. Yourswitch may come with som

-15-2.9 LED IndicationLED Function State InterpretationPOWER Power status ON The power is supplied to the switch.OFF The power is not supplied to the

-16-3. Advanced FunctionsTo help a better understanding about the software management interfaces, this chapter describes someadvanced functions provid

-17-3.2 QoS FunctionThe switch provides a powerful Quality of Service (QoS) function to guide the packet forwarding infour priority classes. The versa

-18-3.2.1 Packet Priority ClassificationEach received packet is examined and classified into one of four priority classes, Class 3, Class 2,Class 1 an

-19-3.3 VLAN FunctionThe switch supports port-based VLAN, 802.1Q Tag VLAN and eight VLAN groups.3.3.1 VLAN OperationThe following figure illustrates t

-2-(C) 2007 KTI Networks Inc. All rights reserved. No part of this documentation may be reproducedin any form or by any means or used to make any dire

-20-3.3.2.3 Drop Untag Per Port SettingEnable - All untagged packets and priority-tagged packets are dropped. A priority-tagged packetis treated as a

-21-3.3.5 VLAN Group Table ConfigurationThe switch provides a table of eight VLAN groups to support up to eight VLANs at the same time.Each VLAN group

-22-3.3.8 Egress Tagging RulesEgress Tagging rules are used to make change to the packet before it is stored into egress queue of anegress port. Three

-23- An 802.1X authenticator: This is the port on the switch that has services to offer to an end device,provided the device supplies the proper cred

-24-4. Web ManagementThe switch features an http server which can serve the management requests coming from any webbrowser software over TCP/IP networ

-25-4.3 Main Management MenuConfigurationSystem Switch information, system and IP related settingsPorts Port link status, port operation mode configur

-26-4.4 System

-27-Configuration DescriptionMAC Address The MAC address factory configured for the switchIt can not be changed in any cases.S/W Version The firmware

-28-4.4.1 Management VLANManagement VLAN settings allow administrator to access the switch and perform the switch manage-ment over a dedicated VLAN.Th

-29-4.5 PortsConfiguration FunctionEnable Jumbo Frames Select to enable jumbo frame supportPort The port numberLink Speed and duplex status with green

-3-The information contained in this document is subject to change without prior notice. Copyright (C). AllRights Reserved.TRADEMARKSEthernet is a reg

-30-4.5.1 SFP DDM StatusDDM (Digital Diagnostic Monitoring) information and status are provided in some SFP transceivers.Part of the information are r

-31-4.6 VLANsVLAN Configuration DescriptionVLAN Disable Select to disable VLAN functionAll ports are allowed to communicate with each others freely wi

-32-4.6.1 Port-based VLAN ModeConfiguration DescriptionGroup 1, 2 Port-based VLAN group numberMember ports Select member ports for the group[Apply] Cl

-33-4.6.2 Port-based VLAN ISP ModeConfiguration DescriptionJoint port Select a port as the joint port for all 5 port-based VLAN groups[Apply] Click to

-34-4.6.3 Advanced VLAN ModeConfiguration DescriptionIngress Default Tag Click to configure per port Ingress Default Tag settingsIngress Settings Clic

-35-4.6.3.1 Ingress Default TagConfiguration DescriptionPort Port numberPVID Port VID, VID for Ingress Default Tag1 ~ 4095 - decimal 12-bit VID valueC

-36-4.6.3.2 Ingress SettingsConfiguration DescriptionPort Port numberTag Aware Check tag data for every received packetTag-aware - set to activate Tag

-37-Note:1. Priority-tagged packet (VID=0) is treated as untagged packet in the switch.2. [Tag Aware] setting affects the index used for VLAN classifi

-38-Configuration DescriptionPort Port numberInsert Tag Activate tagging (Insert a tag to the packet)Enable - set to activate taggingDisable - set to

-39-4.6.3.4 VLAN GroupsConfiguration DescriptionGroup Group numberVID VID of the VLAN to which this group is associated1 ~ 4095 - decimal 12-bit VID v

-4-Table of Contents1. Introduction... 61.1 Features

-40-4.6.4 Important Notes for VLAN ConfigurationSome considerations should be checked in configuring VLAN settings:1. Switch VLAN Mode selectionIt is

-41-4.7 AggregationConfiguration DescriptionGroup Trunk group numberPort # Click to select the port as member port of the trunk group[Apply] Click to

-42-4.8 LACPConfiguration DescriptionPort Port numberProtocol Enabled Enable LACP support for the portKey Value An integer value assigned to the port

-43-4.9 RSTPConfiguration DescriptionSystem Priority The lower the bridge priority is the higher priority it has. Usually, the bridgewith the highest

-44-Aggregations Enabled to support port trunking in STP. It means a link aggregate istreated as a physical port in RSTP/STP operation.Port Protocol E

-45-Configuration DescriptionMode Disabled - disable 802.1X functionEnabled - enable 802.1X functionRADIUS IP IP address of the Radius serverRADIUS UD

-46-4.10.1 802.1X Re-authentication ParametersConfiguration DescriptionReauthentication Enabled Check to enable periodical re-authentication for all p

-47-4.11 MirroringConfiguration DescriptionMirror Port The port is forwarded all packets received on the mirrored portsMirror Source Select the ports

-48-4.12 Quality of ServiceQoS Configuration DescriptionPort Port number802.1p 802.1p priority classificationEnable - set to enable this classificatio

-49-4.12.1 802.1p MappingConfiguration DescriptionPort n Port number ntag m 3-bit User priority tag value m ( range : 0 ~ 7 )Priority class Mapped pri

-5-4. Web Management ... 244.1 Start Browser Software and Making C

-50-4.12.2 DSCP MappingConfiguration DescriptionDSCP [0-63] Seven user-defined DSCP values which are configured with a priority class0 ~ 63 - 6-bit DS

-51-4.12.3 QoS Service PolicyConfiguration DescriptionPort Port numberPolicy Service policy for egress priority among four egress class queuesStrict p

-52-4.13 Storm ControlConfiguration DescriptionBroadcast Rate The rate limit of the broadcast packets transmitted on a port.Broadcast Rate The rate li

-53-4.14 Statistics OverviewStatistics DescriptionPort Port numberTx Bytes Total of bytes transmitted on the portTx Frames Total of packet frames tran

-54-4.15 Detailed StatisticsButton Description[Port #] Click to display the detailed statistics of Port #.[Clear] Click to reset all statistic counter

-55-4.16 LACP StatusStatus DescriptionPort The port numberNormal Display the ports not LACP enabled.Group # The LACP groupStatus The LACP port status

-56-Status DescriptionPort The port numberProtocol Active yes - the port is link up and in LACP operationno - the port is link down or not in LACP ope

-57-4.17 PingPing DescriptionTarget IP Address The target IP address to which the ping command issuesCount The number of ping commands generatedTime O

-58-4.18 Reboot SystemThis menu is used to reboot the switch unit remotely with current configuration. Starting this menu willmake your current http c

-59-5. SNMP SupportSNMP version support Snmp v1, v2c managementManaged Objects MIB-IIsystem OBJECT IDENTIFIER ::= { mib-2 1 }interfaces OBJECT IDENTIF

-6-1. IntroductionThe KGS-612F is a managed Gigabit Ethernet switch which is featured with the following switchedports: Three 10/100/1000Mbps Gigabi

-60-Appendix. Factory Default SettingsSystem ConfigurationDHCP Enabled Not select (disabled)Fallback IP Address 192.168.0.2Fallback IP Subnet mask 255

-61-Ingress Setting - Tag Aware Tag-ignore for all portsIngress Setting - Keep Tag Enable for all portsIngress Setting - Drop Untag Disable for all po

-62-Protocol Enabled Not select (disabled) for all portsKey Value auto for all portsRSTP System ConfigurationSystem Priority 32768Hello Time 2Max Age

-63-Quality of Service Configuration802.1p Classification Disable for all portsDSCP Classification Disable for all portsPort Priority Class 3 for all

-64-DSCP 5 / Priority 0, Class 0DSCP 6 / Priority 0, Class 0DSCP 7 / Priority 0, Class 0All others DSCP Class 0QoS Service PolicyPort 1 Strict priorit

-7-1.1 Features Provides 6 10/100/1000Mbps RJ-45, one 1000M SFP and two 100M SFPs Provides in-band web-based management interface All copper ports

-8-1.3 LED IndicatorsLED FunctionPOWER Power statusLNK/1000M/ACT Network port 1000M link status (Port 1 - Port 6)LNK/100M/ACT Network port 100M link

-9-Combo Ports with 10/100/1000 RJ-45 and 100Mbps SFPCopper interfaceCompliance IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX,IEEE 802.3u 1000Base-TConn