KTI Networks KSC-200 Installationsanleitung

-1-IndustrialSerial RS-232 to Fiber ConverterKSC-200 SeriesInstallation GuideDOC.111209-KSC-200

-10-CertificateFCC Part 15 Class BCE/EMC EMI EN50081-1 Class BEMS EN55024CE/LVD Safety EN 60950EN55022EN61000-3-2EN61000-3-3EN 55024IEC 61000-4-2 ESD

-11-2. Installation2.1 UnpackingCheck that the following components have been included:• Information CD• The device unit• DIN-rail mounting bracketIf

-12-2.2 Safety CautionsTo reduce the risk of bodily injury, electrical shock, fire, and damage tothe equipment, observe the following precautions.• D

-13-2.3 DIN-Rail MountingIn the product package, a DIN-rail bracket is installed on the device formounting the converter in a industrial DIN-rail encl

-14-The final mechanical dimensions after installing DIN rail mounting bracketare:

-15-2.4 Panel MountingThe device is provided with an optional panel mounting bracket. Thebracket support mounting the device on a plane surface secure

-16-The screw locations and final dimension are shown below:

-17-2.5 Applying PowerThe power specifications of the device are:Operating Voltage +7 ~ +30VDCPower Consumption Max. 2.4W @30VDCThe device provides t

-18-Power wires: 24 ~ 12AWG (IEC 0.5~2.5mm2)Install the power source wires with the plug properly. Screw the wire withplug securely. Then, plug in DC1

-19-Using DC Power JackDC Jack Connector: Jack D 6.3mm D 2.0mmAC Power Adapters: Optional commercial rated adapters are availablefor purchasing.Rate

-2-(C) 2006 KTI Networks Inc. All rights reserved. No part of this documen-tation may be reproduced in any form or by any means or used to makeany dir

-20-2.6 Power Failure Relay OutputThe device provides a relay output to report power failure event to aremote alarm monitoring system. The replay outp

-21-2.7.1 RS-232 Port Pin Assignment TablePin# Signal Name Input/Output 1 Received Line Signal Detect Output 2 TX Data Output 3 RX Data Input 4 DT

-22-2.7.2 Cable for Connection to PC COM PortConnecting to 9-pin DTE device (Computer or PC COM)Connecting to 25-pin DTE device (Computer or PC COM)

-23-2.8 Making Fiber Port ConnectionDepending on the model purchased, the fiber port provides one of thefollowing connector types: Duplex ST, Duplex S

-24-Connecting Single Mode Single FiberFor Bi-Di (Bidirectional) single fiber connection which use two differentwavelengths for TX and RX respectively

-25-2.9 ApplicationThe converter can be used to extend the distance between two serialdevices via fiber cables. The distance can be 2km, 20km, and eve

-26-3 LED IndicatorsThe following figure shows the locations of the LED indicators:3.1 LED IndicatorsLED DISPLAY STATE INTERPRETATIONPWR Power status

-27-Appendix: Model Optical SpecificationsModel Fiber Port SpecificationsModel FX Wavelength Tx Power Sensitivity Max.Rx200-T ST 1310nm -20~-14 -32dBm

-3-The information contained in this document is subject to change withoutprior notice. Copyright (C) All Rights Reserved.TRADEMARKSEthernet is a regi

-4-Table of Contents1. Introduction...51.1 Features ...

-5-1. IntroductionThe converter is designed to provide the most versatile connection pos-sible between two RS-232 serial equipment using fiber optic c

-6-1.1 Featuresz Transparent conversion for all RS-232 signalsz Supports RS-232 baud rate higher than 115.2K bpsz Auto adaptation and conversion to an

-7-1.2 SpecificationsThis figure shows the important components of the device:

-8-Serial Interface (RS-232 Port)Connector DB9 femalePin Assignments DCE typeIsolation RS-232 I/O and internal systemBaud Rate Support Auto-detect, Up

-9-DC Power InterfaceInterface Screw-type terminal block 1. Two pairs for power wire cascading 2. One pair for power failure relay outputDC Jack (-6